System Configuration Utility Advanced Troubleshooting Settings
ID: Q181966
|
The information in this article applies to:
SUMMARY
This article describes the advanced troubleshooting settings in the System
Configuration Utility tool.
MORE INFORMATION
To start the System Configuration Utility and view the advanced
troubleshooting settings, use the following steps:
- Click Start, and then click Run.
- In the Open box, type msconfig, and then
click OK.
- Click Advanced.
Advanced Troubleshooting Settings
Disable System ROM Breakpoint:
This setting specifies whether Windows 98 should use Read Only Memory
(ROM) address space between F000:0000 and 1 megabyte (MB) for a break
point. Windows normally searches this address space to find a special
instruction that is used as a system break point. If this address space
contains something other than permanently available ROM, you should
disable this setting. This sets "SystemROMBreakPoint=0" in the System.ini
file. This is equivalent to starting Windows with the command-line switch
"/d:s".
For additional information about SystemROMBreakPoint, please see the
following article in the Microsoft Knowledge Base:
ARTICLE-ID: Q71264 Q71264
TITLE : Information on SYSTEM.INI [386enh] Entry SystemROMBreakPoint=
Disable Virtual HD IRQ:
This setting prevents Windows 98 from terminating interrupts from the hard
disk controller and bypassing the ROM routine that processes these
interrupts. Some hard disk drives may require this setting to be enabled
for interrupts to be processed correctly. If this setting is enabled, the
ROM routine handles the interrupts, which can slow system performance.
This sets "VirtualHDIRQ=0" in the System.ini file. This is equivalent to
starting Windows with the command-line switch "/d:v".
EMM Exclude A000-FFFF:
This setting prevents Windows from trying to scan for unused memory
address space. This also disables the Random Access Memory (RAM) and ROM
search instructions for the memory address space. This scanning can
interfere with some devices that use the same memory addresses. This sets
"EMMExclude=a000-ffff" in the System.ini file. This is equivalent to
starting Windows with the command-line switch "/d:x".
Force Compatibility Mode Disk Access:
This setting prevents all 32-bit disk drivers from being loaded except the
floppy driver. You may want to enable this setting if your computer does
not start due to disk peripheral input/output (I/O) problems. If you
enable this setting, all I/O uses real-mode drivers or the basic
input/output system (BIOS). Also, all disk drives that are functional in
protected mode only, no longer function. This is equivalent to starting
Windows with the command-line switch "/d:f".
VGA 640 x 480 x 16:
This setting causes Windows 98 to use the standard VGA display adapter
driver. This disables the existing "display.drv=" line of the System.ini
file, and adds the "display.drv=vga.drv" line to the [boot] section of the
System.ini file.
Use SCSI Double-Buffering:
Some Small Computer System Interface (SCSI) drives may require that this
setting be enabled. Windows 98 should detect whether or not this setting
is needed, so you should only enable this setting if there is a disk
access problem. This adds the line "Doublebuffer=2" to the Msdos.sys file.
This setting is unavailable if a Doublebuffer line already exists in the
Msdos.sys file.
Disable Scandisk After Bad Shutdown:
This setting adds the line "Autoscan=0" to the Msdos.sys file. This can be
useful when you troubleshoot shutdown issues, as it decreases startup time
after a bad shutdown.
Limit Memory to <x> MB:
This setting limits memory usage on your computer to the first <x> MB,
where <x> is a number of megabytes. This setting adds the
"MaxPhysPage=<nnn>" line to the System.ini file, where <nnn> is a
hexidecimal value of the amount of memory to be used. If this setting is
too low (16 MB or lower), it may prevent Windows 98 from starting
normally.
Disable Fast Shutdown:
This setting disables Windows 98 shutdown performance enhancements. This
can be useful to troubleshoot problems shutting down Windows 98.
Disable UDF File System:
This setting disables support for the Universal Disk Format (UDF) file
system for all removable media. This setting can be used to troubleshoot
problems with proprietary DVD players that may be incompatible with UDF.
Enable Pentium F0 (Lock CmpXchg):
This setting provides a method to work around an erratum in the Intel P5
series of processors (Pentium and Pentium MMX). The processor stops
responding (hangs) if a particular illegal instruction sequence is issued.
This issue should not occur with a normal program, it would have to be
generated maliciously. If this setting is enabled, Windows 98 enables a
protection routine to avoid hanging. This setting can interfere with some
kernel mode applications (such as debuggers), so it should not be used
while debugging programs.
NOTE: Norton Utilities 3.0 SpeedDisk and UnErase Wizard tools lock the
computer if used with this setting enabled. If you have Norton Utilities,
Microsoft recommends that you do not use this setting, or disable Norton
Utilities from startup.
For additional information about Win.com command-line switches, please see
the following article in the Microsoft Knowledge Base:
ARTICLE-ID: Q142544
TITLE : Windows 95 Win.com Command-Line Switches
For additional information about file system troubleshooting settings,
please see the following article in the Microsoft Knowledge Base:
ARTICLE-ID: Q165503
TITLE : Description of the File System Troubleshooting Options
For additional information about troubleshooting memory issues, please see
the following article in the Microsoft Knowledge Base:
ARTICLE-ID: Q134503
TITLE : Parity Error Messages May Indicate Bad Memory
For additional information about the Msdos.sys file, please see the
following article in the Microsoft Knowledge Base:
ARTICLE-ID: Q118579
TITLE : Contents of the Windows Msdos.sys File
Additional query words:
98
Keywords : kbenv kbtool win98
Version : WINDOWS:
Platform : WINDOWS
Issue type : kbinfo
Last Reviewed: January 30, 1999