DOCUMENT:Q69843 04-FEB-2002 [win95x] TITLE :Windows Err Msgs: Lotus 1-2-3 Version 3.1 and Windows PRODUCT :Microsoft Windows 95.x Retail Product PROD/VER::3.0,3.0a,3.1,3.11 OPER/SYS: KEYWORDS: ====================================================================== ------------------------------------------------------------------------------- The information in this article applies to: - Microsoft Windows versions 3.0, 3.0a, 3.1, 3.11 ------------------------------------------------------------------------------- SUMMARY ======= This article discusses error messages that may be returned when you run Lotus 1-2-3 version 3.1 from Microsoft Windows. MORE INFORMATION ================ The following error messages may be returned when you run Lotus 1-2-3 version 3.1 from Windows 3.0 or 3.0a in real or standard mode or from later versions of Windows in standard mode: VM error[27] ------------ VM error[27]: Not enough disk space for swap file "d:\XXXXXXXXX'" (where XXXXXXXXX is a file name) This indicates that Lotus 1-2-3 has its swap file path set to a directory that does not have sufficient space to create the swap file. To work around the problem, try the following: 1. Specify the SET 123SWAPPATH statement (located in the AUTOEXEC.BAT file) to point to another drive that has sufficient space. 2. Reduce the amount of memory allocated for Lotus 1-2-3 by adjusting the SET 123MEMSIZE statement to a lower value. 3. Back up and erase all nonessential files from the hard drive to provide more disk space for the swap file. VM error[26] ------------ VM error[26]: Cannot create swap file. Make sure the 123SWAPPATH statement in your AUTOEXEC.BAT file contains only existing directories and no diskette drives. "name= g:\XXXXXXXXX" (where XXXXXXXXX is a filename) This indicates that Lotus has its swap file path set to a directory that does not exist. To work around the problem, set the SET 123SWAPPATH statement (located in the AUTOEXEC.BAT file) to point to another drive that exists and has sufficient disk space. ENHANCED MODE ------------- The following error message may be returned when Lotus 1-2-3 version 3.1 is run from Windows in enhanced mode: Cannot load driver file xxxx Cannot initialize resident segments (where xxxx refers to the driver filename) This indicates a low-memory situation and frequently occurs on computers configured with two megabytes (MB) of RAM. Under these circumstances, the following changes are recommended to ensure that there is ample available memory to run Lotus 1-2-3. To work around the problem: 1. Remove or reduce the size of SMARTDrive. Normally, 2 MBs is not enough memory to load program code in physical memory if SMARTDrive consumes too much RAM. If there is insufficient physical RAM and/or insufficient swap file space, MS-DOS applications (that is, non-DPMI applications) will not be able to load into memory. It's better to run a program slower (that is, without caching support) rather than not having enough memory to run it at all. 2. Ensure that there is sufficient swap file space. For more information about swap file, query on: enhanced and mode and 2 mb 3. Use the standard PIF settings from either the 123.PIF, supplied with Lotus, or the _DEFAULT.PIF, supplied with Windows. Lotus 1-2-3 must have at least 64K of XMS memory available to run. 4. Verify that the SET statements included in the AUTOEXEC.BAT file are correct. Because Lotus 1-2-3 3.1 has both DPMI and virtual memory support, optional SET statements can be added to adjust the program's memory usage. The SET 123MEMSIZE= statement (in the AUTOEXEC.BAT file) controls the total memory consumption (physical and virtual memory) by Lotus 1-2-3. This should not exceed the amount of memory available in Windows. Please refer to the "Setting Up 1-2-3" section in the "Lotus User Manual" for more information on configuration, syntax on SET statements, and Windows-related issues. The Lotus product included here is manufactured by a vendor independent of Microsoft; we make no warranty, implied or otherwise, regarding this product's performance or reliability. REFERENCES ========== "Lotus 1-2-3 User Manual," version 3.1, "Setting Up 1-2-3" Additional query words: 3.00 3.0 3.0a 3.00a 3.10 3.113rdparty low memory 386 ====================================================================== Keywords : Technology : kbWin3xSearch kbZNotKeyword3 kbWin300 kbWin300a kbWin310 kbWin311 Version : :3.0,3.0a,3.1,3.11 ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 2002.