Redirector Memory Requirements

ID: Q122123

2.20 2.20a 2.20b 3.11 | 3.10 3.11 MS-DOS | WINDOWS kbnetwork kbinterop

The information in this article applies to:

Microsoft LAN Manager versions 2.2, 2.2a, 2.2b
Microsoft Workgroup Add-On for MS-DOS version 3.11
Microsoft Workgroup Connection version 3.1
Microsoft Windows for Workgroups version 3.11

SUMMARY

The type of network client you choose to use sometimes depends on the amount of memory the network operating system requires. This article discusses the amount of memory that the different network clients use before any protocol drivers are loaded.

MORE INFORMATION

The following chart shows the memory, in bytes, used by the different modules for each of the different MS-DOS network clients. The memory module is listed on the top, and the network client is listed on the left.

            PROTMAN NDISHLP  REDIR   BASIC WORKGRP  NETWKSTA  Total

Add-On Full 2,960   1,440    106,752                          111,152
Add-On Bas. 2,960   1,440            13,696                   18,096
2.20 Enh.   6,224                                   94,224    100,448
2.20 Basic  6,224            38,768                           44,992
2.2a Enh.   6,224                                   94,672    100,896
2.2a Basic  6,224            38,768                           44,992
2.2b Enh.   6,240                                   94,688    100,928
2.2b Basic  6,240            38,768                           45,008
WFW Full    2,960*  1,440    91,792                           96,192
WFW Basic   2,960*  1,440            12,000                   16,400
WFW Win     2,960*  1,440                                     4,400
MSWGCN Full 128              86,064        4,368              90,560
MSWGCN Bas. 128                            4,368    47,936    52,432

For clarity, the full name and versions of the abbreviations used above are as follows:

   Add-On Full  =  Workgroup Add-On for MS-DOS, NET START FULL
   Add-On Bas.  =  Workgroup Add-On for MS-DOS, NET START BASIC
   2.20 Enh.    =  LAN Manager 2.2.0, Enhanced
   2.20 Basic   =  LAN Manager 2.2.0, Basic
   2.2a Enh.    =  LAN Manager 2.2a.0, Enhanced
   2.2a Basic   =  LAN Manager 2.2a.0, Basic
   2.2b Enh.    =  LAN Manager 2.2b, Enhanced
   2.2b Basic   =  LAN Manager 2.2b, Basic
   WFW Full     =  Windows for Workgroups, NET START FULL
   WFW Basic    =  Windows for Workgroups, NET START BASIC
   WFW Win      =  Windows for Workgroups loading the network when Windows
                   starts.
   MSWGCN Full  =  Workgroup Connection, NET START FULL
   MSWGCN Bas.  =  Workgroup Connection, NET START BASIC

* NOTE: If only protected mode protocols are being used, then PROTMAN takes up only about 400 bytes of memory when issuing either NET START FULL or NET START BASIC command. If you have Windows for Workgroups using only protected mode network drivers, and you only issue a NET START command, then none of the drivers listed above load in the memory under 1 megabyte (MB).

Additional reference words: wfw wfwg prodlm 3.10 minimum maximum KBCategory: kbnetwork kbinterop KBSubcategory: ntnetserv ntdriverdevdrvr ntinterop ntprotocol

Keywords          : NTInterop ntnetserv ntprotocol ntdriverdevdrvr 
Version           : 2.20 2.20a 2.20b 3.11 | 3.10 3.1
Platform          : MS-DOS WINDOWS

Last Reviewed: September 10, 1996