DOCUMENT:Q145592 08-AUG-2001 [winnt] TITLE :I/O Channel Ready Settings on the Intel EtherExpress 16 PRODUCT :Microsoft Windows NT PROD/VER:3.11 3.50 3.51 OPER/SYS: KEYWORDS: ====================================================================== ------------------------------------------------------------------------------- The information in this article applies to: - Microsoft Windows NT Workstation versions 3.5, 3.51 - Microsoft Windows NT Server versions 3.5, 3.51 - Microsoft Windows for Workgroups version 3.11 ------------------------------------------------------------------------------- SUMMARY ======= When you install the driver for the Intel EtherExpress 16 local area network adapter, one of the configuration fields is I/0 Channel Ready. This option can have three possible values: Late, Early, and Never. Typically, Windows NT will only allow the user to set this field to Later or Never. This article includes configuration information for both Windows NT and Windows for Workgroups. MORE INFORMATION ================ The I/O Channel Ready settings optimize the timing of 16-bit data transfers. The Never value forces the card into 8-bit mode; the Late and Early values both allow the card to work in 16-bit mode. The setting that works on most computers is Late, although a few computers require Early to function in 16-bit mode. Some computers will experience problems when the card is set to Early. These problems can range from data loss when transferring large files to computer hangs that require removing the card, transferring it to another computer and using the Softset utility to reset the network adapter. Windows NT ---------- Because of the potential for serious problems, Windows NT setup does not offer Early as one of the options unless one of the following is true: - Setup detects that the card is already set to Early. -or- - The .INF file for the Intel EtherExpress has been modified to allow the early setting. Even when the Early option is available, if you select it, you will receive the following error message: Use of the Early setting may cause system failure in some machines. Are you sure you want to continue? While those computers that require Early will not function when the card is set to Late, the EtherExpress driver is capable of detecting this case and it will default the card to Never, which is always safe. Unfortunately, there is no way to detect when Early is not safe without experiencing the problems mentioned above. If you have a computer that requires the Early setting and it is not displayed as an option in Windows NT, you can add Early to the list by doing the following: 1. Open the OEMNADIN.INF file in the %systemroot%\SYSTEM32 subdirectory with a text editor. 2. Find the line that reads "AllowEarly =" and change the value after the equal sign from 0 to 1. 3. Save the file. 4. Use the network applet in Control Panel to configure the network adapter settings. Early should then show up as an option for I/O Channel Ready. Windows for Workgroups ---------------------- When you install the network adapter and run the Softset utility in Windows for Workgroups, both the Softset and Windows for Workgroups stop responding (hang). If your network adapter has the Early setting and you want to change it to the Late setting: 1. Obtain E16LATE.EXE, a self-extracting file, from one of the following locations: - Intel World Wide Web site (http://www-cs.intel.com/all/selfhelp/6263.HTM) - Intel FTP server (ftp://ftp.intel.com/pub/PCandNetworkSupport/EtherExpress) - Intel Bulletin Board Service at (503) 264-7999 2. In the CONFIG.SYS file, remark out the following line with REM using a text editor, such as EDIT.COM: REM DEVICE=:\EXP16.DOS 3. Save CONFIG.SYS and reboot your computer. 4. Using a text editor, modify the lines in PROTOCOL.INI file to the following: IOCHRDY=LATE IOADDRESS= 5. Save PROTOCOL.INI. 6. Run LATE.EXE (one of the files extracted from E16LATE.EXE) utility. This utility resets the EEPROM of the Etherexpress NIC I/O Channel Ready to the current IOCHRDY information from PROTOCOL.INI. 7. In the CONFIG.SYS file, remove REM for EXP16.DOS, as follows: DEVICE=:\EXP16.DOS 8. Power down the computer and wait a few seconds. 9. Turn the computer on restart Windows for Workgroups. The third-party products discussed here are manufactured by vendors independent of Microsoft; we make no warranty, implied or otherwise, regarding these products' performance or reliability. Additional query words: prodnt 3.11 ether express ====================================================================== Keywords : Technology : kbWinNTsearch kbWinNTWsearch kbWinNT351search kbWinNT350search kbWinNTW350 kbWinNTW350search kbWinNTW351search kbWinNTW351 kbWinNTSsearch kbWinNTS351 kbWinNTS350 kbWinNTS351search kbWinNTS350search kbAudDeveloper kbWFWSearch kbWFW311 Version : 3.11 3.50 3.51 ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 2001.