DOCUMENT:Q96149  30-JUL-2001  [lanman]
TITLE   :Installing Wollongong Pathway Access on WfW
PRODUCT :Microsoft LAN Manager
PROD/VER:
OPER/SYS:
KEYWORDS:

======================================================================
SUMMARY
=======

Wollongong Group's Pathway Runtime and Pathway Access 1.2 can be used with
Windows for Workgroups. Pathway Runtime is Wollongong's TCP/IP stack and Pathway
Access is a set of TCP/IP utilities provided by Wollongong. This article
provides you with the steps that are needed to install Pathway Runtime 1.2 on
Windows for Workgroups 3.1.

Note: Microsoft Product Support Services does not support Pathway Runtime or
Pathway Access. This information is provided for user information only.

MORE INFORMATION
================

Pathway Runtime is Wollongong Group's TCP/IP stack. The product comes with an
RFC compliant NetBIOS interface and can be used with Windows for Workgroups.

To install Pathway Runtime from Wollongong Group on Windows for Workgroups, do
the following:

1. Install Pathway Runtime using PWSETUP.EXE from the DOS Setup Disk.

2. Complete the installation using the complete NDIS installation option. (For
   more information, please refer to the Pathway Runtime manual.

3. After the installation is complete, change the AUTOEXEC.BAT file such that
   the "net start" command is executed immediately before the PWTCP command and
   after the NDIS command. Following is an example of the AUTOEXEC.BAT file
   after the changes:

   rem #------------------------ The Wollongong Group --------------------#
   rem #  The following lines are for PathWay Runtime setup. Please DO NOT#
   rem #  modify or remove any of them. If you DO want to, please run the #
   rem #  setup program to modify or deinstall PathWay for DOS.           #
   SET PATH=C:\PATHWAY;%PATH%
   PWCONFIG -N:65
   NDIS -I:5 -D:3
   net start
   PWTCP
   c:\pathway\NetBIOS
   rem #------------------------ The Wollongong Group -------------------#

4. Make sure that the -I option for the NDIS command refers to the IRQ being
   used by the network card. The -D option refers to the paragraph number in
   PROTOCOL.INI referring to the network card.

5. Run NETBIOS.EXE after PWTCP.EXE. NETBIOS.EXE is the RFC 1001/1002 compliant
   driver.

6. Edit the SYSTEM.INI file in the Windows subdirectory and add the following
   line to the [386enh] section:

      V86ModeLanas=0

   This will indicate that the real mode protocol stack will be using Lana 0.
   Note that Pathway Runtime can only use Lana 0.

7. Reboot and start Windows.

Pathway Access can now be installed if needed by following instructions provided
by Wollongong.

Reference(s):

Wollongong Pathway Access Release Notes Windows for Workgroups Resource Kit

Additional query words: wfw wfwg 3.10

======================================================================
Keywords          :  

=============================================================================

THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS
PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND.  MICROSOFT DISCLAIMS
ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  IN NO
EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR
ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF
MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.  SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES
SO THE FOREGOING LIMITATION MAY NOT APPLY.

Copyright Microsoft Corporation 2001.