DOCUMENT:Q66292  17-DEC-2000  [msdos]
TITLE   :Reading Text Files into MS-DOS Environment Variables
PRODUCT :Microsoft Disk Operating System
PROD/VER:MS-DOS:3.x,4.x,5.0,6.0,6.2,6.21,6.22
OPER/SYS:
KEYWORDS:msdos

======================================================================
-------------------------------------------------------------------------------
The information in this article applies to:

 - Microsoft MS-DOS operating system versions 3.1, 3.2, 3.21, 3.3, 3.3a, 4.0, 4.01, 5.0, 6.0, 6.2, 6.21, 6.22 
-------------------------------------------------------------------------------

SUMMARY
=======

This article describes the several steps needed to use the results of a query
(using the FIND filter) as a replaceable parameter in a one or more batch files.
A use for this would be to search for a specific file and then perform some
action on or with this file. The file could then be used in one or more batch
files as a replaceable parameter.

MORE INFORMATION
================

First, you need to set up a one-line file with the partial command

   set varname=

with no carriage return (CR) or linefeed (LF) at the end (this can be done with
COPY CON by pressing CTRL+Z after the equal sign [=] and pressing ENTER).

The file would look like this on the screen:

   C:\>COPY CON INIT.TXT
   SET VARNAME=^Z

The following steps can be issued from the MS-DOS command prompt or from within a
batch file:

1. Search for a single directory entry and place the results in a text file.

      dir | find "dos" > textfile

2. Append the two files into one batch file using the COPY command as follows:

      copy init.txt+textfile varset.bat

3. Place the contents of the text file in a variable by running VARSET.BAT.

VARSET.BAT sets an environment variable equal to the directory entry found
earlier. This allows the environment variable to be used as a replaceable
parameter in later batch files. VARSET.BAT can be called from the command prompt
or from within another batch file.

NOTE: This process works for directory names only if MS-DOS 5.0 or 6.0 is being
used. Under MS-DOS 5.0 and 6.0, the /B switch must be used when you are
searching for a directory name. The following is an example of searching for a
directory under MS-DOS 5.0 or 6.0.

   dir /b | find "dos5" > textfile

NOTE: There is still a 127-character limit to the length of this variable, which
includes the variable name and equal sign (=).

Additional query words: 6.22 3.x 4.x 5.00 5.00a 6.00 6.20

======================================================================
Keywords          : msdos 
Technology        : kbMSDOSSearch kbMSDOS321 kbMSDOS400 kbMSDOS320 kbMSDOS330a kbMSDOS621 kbMSDOS622 kbMSDOS620 kbMSDOS600 kbMSDOS310 kbMSDOS500 kbMSDOS330 kbMSDOS401
Version           : MS-DOS:3.x,4.x,5.0,6.0,6.2,6.21,6.22

=============================================================================

THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS
PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND.  MICROSOFT DISCLAIMS
ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  IN NO
EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR
ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF
MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.  SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES
SO THE FOREGOING LIMITATION MAY NOT APPLY.

Copyright Microsoft Corporation 2000.