ID: Q69698
The information in this article applies to:
When you save a document in "Text With Layout" or "MS-DOS Text With Layout" format, the Microsoft Word converter uses a character size of 10 pitch to determine the maximum number of characters that can appear on a single line in the output file. (This is independent of the font sizes in the original Word document.) To determine the number of characters per line, the converter multiplies the number of characters per inch (CPI) by the amount of horizontal printable space.
For example, if a document has an 8.5-inch page width, and left and right margins of 1.25-inch (the default setting in Word), the amount of horizontal printable space is 6 inches. When the Word document is converted to a text file with the "Text With Layout" converter, 10 CPI multiplied by 6 inches of printable space determines that the output text file will contain a maximum of 60 characters per line. If one or more lines in the original Word document contain more than 60 characters, the lines of text are wrapped, and the remaining text appears on the following line.
When you convert complex document formatting to an ANSI or ASCII text file, the converter must make several assumptions. For example, if a document contains several pitch sizes on a single line, which size would the converter use to determine line length? (The first font size? The largest font size?) A text file does not allow for these variations. The default assumption of 10 CPI in the design of this converter is the best compromise that can be made to most consistently accommodate the generalized conversion scenario. If this assumption does not facilitate your export needs, make use of the PointSize or Width flags to change the assumptions made by the converter.
Converter Option Description
------------------------------------------------------------------------
PointSize=n This option can be used to customize the CPI
assumption used by the converter. By default,
PointSize is set to 12. A 12-point font is
equivalent to a 10-pitch font; thus, the
converter uses a default of 10-CPI. By changing
the PointSize value to a smaller number, you
can increase the number of characters allowed
per line.
For example, if you change PointSize to 10, the
converter assumes 12 CPI. 12 CPI multiplied by
6-inches of printable space determines that the
converter will allow 72 characters per line.
Width=n This option is the ultimate determinant of line
length. By default, it is set to 80-character
columns, which is also the maximum number of
characters allowed in a column. By specifying a
smaller value, you can force lines to wrap
earlier in the export text file. For example,
by changing this setting to 50, Word will allow
a maximum of 50 characters per line in the
export file.
ARTICLE-ID: Q50987
TITLE : WD: Definitions of Typography Terms in Word for Windows
ARTICLE-ID: Q36401
TITLE : WD: Definitions of Typography Terms in Word for the
Macintosh
NOTE: The default settings for PointSize and Width are Width=80 and PointSize=12.
To change the Width= and PointSize= settings:
1. Run the EditConversionOptions macro.
Do this by first opening Convert.dot, which is located in the
Macros directory in the under the Word program directory (usually
C:\Msoffice\Winword\Macros).
3. In the Macro dialog box, select the EditConversionOptions macro and
click Run.
5. In the Conversion Option box, select Width=80. In the Setting box, type
the maximum number of characters that you want to appear on a line.
box, type in the point size you want.
The settings are stored in the [TextLytConv] section of the Mstxtcnv.ini file.
To change the Width= and PointSize= settings:
1. Run the EditConversionOptions macro.
Do this by first opening Convert.dot, which is located in the
Macros directory in the under the Word program directory (usually
C:\Winword\Macros).
3. In the Macro dialog box, select the EditConversionOptions macro and
click Run.
5. In the Conversion Option box, select Width=80. In the Setting box, type
the maximum number of characters that you want to appear on a line.
box, type in the point size you want.
The settings are stored in the [TextLytConv] section of the Win.ini file. You can view and change the options for each converter in Word using the following steps:
1. On the Tools menu, click Options.
2. Under Category, select Win.ini.
3. In the Application Box, select TextLytConv from the drop-down list.
4. In the Startup Options box, select the converter option you want to
modify. For example, select Width=80.
then click Set. For example, change 80 to 72 in the Setting box and then
click Set.
NOTE: You can delete an option by selecting it and then clicking Delete.
For more information on how to modify these settings, see the Convinfo.doc document located in your Word program directory.
1. Run the EditConversionOptions macro.
Do this by first opening Conversion Macros document, which is located in
the Macros directory in the under the Word program directory.
3. In the Macro dialog box, select the EditConversionOptions macro and
click Run.
5. In the Conversion Option box, click the Width=80 option. In the
Setting box, type the maximum number of characters that you want
to appear on one line.
the Setting box, type in the point size you want.
The same two options are available in the "MS Word Conversion Options" file located in the Word Commands sub-folder in the Word for the Macintosh folder on your Macintosh system. For more information on how to modify these settings, see the Conversion Information document located in your Word for the Macintosh folder.
Additional query words: smart txtwlyt
Keywords : kbconversion wordnt winword ntword macword word6 word7 word95
Version : MACINTOSH:5.0,5.1,6.x;WINDOWS:1.x,2.x,6.x,7.x,97Last Reviewed: November 10, 1998