Plug and Play Support in Windows Questions and Answers

ID: Q133159


The information in this article applies to:


SUMMARY

This article contains questions and answers about Plug and Play support in Windows.


MORE INFORMATION

  1. Q. What is the difference between detection and enumeration in Windows?

    A. Detection is the process Windows uses during its search for legacy, or non-Plug and Play, devices on a computer. Detection is used during Windows Setup and any time you use the Add New Hardware Wizard to search for new hardware installed in your computer. Detection does not run each time you start Windows. During the detection process, Windows creates a file called Detlog.txt in the root directory of the boot drive. This file exists primarily as a troubleshooting tool.




Enumeration is the process Windows uses to identify Plug and Play devices in your computer, including those devices on Plug and Play busses such as ISAPNP, PCI, and PCMCIA (PC card) devices. Enumeration occurs each time Windows starts and whenever Windows receives notification that a change has occurred in the computer's hardware configuration, such as when you remove a PCMCIA card.

  1. Q. What is Plug and Play?

    A. Plug and Play is both a design philosophy and a set of personal computer architecture specifications with the goal of making the personal computer, add-in hardware devices, drivers, and the operating system work together automatically without user intervention. In order to achieve this goal, all the components must be Plug and Play. The components of a Plug and Play system include:

    Depending on whether any of these components are Plug and Play or not, the level of ease of use and dynamic operation varies. At the lowest level, where all three components are legacy, or non-Plug and Play, the system lacks any dynamic operation and is difficult to use since card jumpers and switches need to be manually set and drivers manually loaded.

    At the next level, when a Plug and Play operating system (such as Windows) is used with legacy hardware, the system supports dynamic operation of PCMCIA devices and is relatively easy to use. Ease of use is enhanced during hardware setup by the Device Wizard (which helps to detect, identify, and configure devices), consistent user interface of device property sheets, and availability of device information through the registry and Device Manager. Additional ease of use is achieved due to automatic loading of drivers using the Device Installer, and due to smart software that reacts to configuration changes to give dynamic hardware event messages.

    At the highest level, where all three components are Plug and Play, installing new devices is as easy as plugging them in and turning on the computer. Hardware setup is completely silent and transparent, and you do not need to modify expansion card jumper settings, or even modify operating system configuration files. Also, due to the Plug and Play BIOS, the system supports full dynamic operation, including hot docking, APM 1.1 power management, automatic configuration of boot devices, and programming of motherboard devices.


  2. Q. There is a device installed in my computer for which I do not want Windows to load drivers or allocate resources. How do I accomplish this?

    A. You can use Device Manager to cause Windows not to load drivers or allocate resources for a device. To do so, follow these steps:

    1. Click the Start button, point to Settings, and then click Control Panel.


    2. Double-click the System icon.


    3. On the Device Manager tab, click the device you want, and then click Properties.


    4. On the General tab, click the Original Configuration (Current) check box to clear it, and then click OK (Windows 95), or click Disable in this hardware profile. (Windows 95 OEM Service Release 2 (OSR2) and Windows 98).




  3. Q. When I installed Windows on my laptop computer, it did not detect or install support for my PCMCIA modem. Why?

    A. Windows automatically identifies, configures, and installs Plug and Play devices, including PCMCIA cards. This requires that 32-bit PCMCIA support be installed, which is disabled by default. To enable this feature, please see the "To enable 32-bit PC card support" topic in Windows Help.


  4. Q. How can I tell if Windows recognizes my PCMCIA card correctly?

    A. To determine whether a PCMCIA card is recognized correctly, use the following steps:

    1. Listen for the insertion tones (beeps) when you insert the card.


    2. Look for the PC card icon on the taskbar.


    3. Check the PC card icon in Control Panel.

      NOTE: If the PC Card Wizard was not already invoked, it will start.




  5. Q. I installed Windows on my laptop computer, but Advanced Power Management (APM) does not seem to be installed. What can I do?

    A. To determine whether APM is installed, check to see if a Suspend command appears on the Start menu. If not, check to see if a Power icon appears in Control Panel. If there is a Power icon, APM is installed. To make the Suspend command available on the Start menu, double-click the Power icon in Control Panel, then click "Always show Suspend command on Start menu." If APM still does not work, follow these steps:

    1. Use the right mouse button to click My Computer, then click Properties on the menu that appears.


    2. On the Device Manager tab, double-click System Devices.


    3. If Advanced Power Management is not listed under System Devices, APM is not installed. Stop here.


    4. If Advanced Power Management is listed under System Devices, click it, and then click Properties.


    5. On the Settings tab, click Enable Power Management if it is not selected, and then click OK.


    If APM is not installed, you must reinstall Windows to install APM support. If APM is not automatically detected on your computer, it is not guaranteed to work.

    NOTE: Even if the Suspend command appears on the Start menu, you may not have full APM support. Please contact your computer manufacturer for details about your computer's APM implementation if certain APM features do not work.


  6. Q. My computer uses a dual-port PCI E/IDE controller but the secondary port is not displayed in Device Manager. Why?

    A. By default, the secondary port is not displayed if no device is attached to it. The secondary port may also not be displayed for the following reasons:



  7. Q. When I insert my laptop computer in its docking station, or remove it from the docking station, Windows does not recognize the change. Why?

    A. Windows recognizes the docking state for some of the more popular laptop computers equipped with a Plug and Play BIOS. If Windows does not recognize the docking state for your computer, you must manually establish docked and undocked profiles and choose which profile you want to load during Windows startup.


Additional query words:


Keywords          : kbenv winpnp win95 win98 
Version           : WINDOWS:95
Platform          : WINDOWS 
Issue type        : kbinfo 

Last Reviewed: June 17, 1999