DOCUMENT:Q80258 10-NOV-1999 [pcmail] TITLE :PC Gen: Contents of Modem Script File IBM5853.MDM PRODUCT :Microsoft Mail For PC Networks PROD/VER:WINDOWS:2.1e OPER/SYS: KEYWORDS: ====================================================================== ------------------------------------------------------------------------------- The information in this article applies to: - Microsoft Mail for PC Networks, version 2.1e ------------------------------------------------------------------------------- SUMMARY ======= The following is the contents of the Microsoft Mail version 2.1e modem script file IBM5853.MDM, which can be compiled with SCRCOMP.EXE: ;********************************************************************* ; ; Microsoft Mail Script File ; ; Filename: ibm5853.mdm ; Date : March 21, 1990 ; Script : Standard script file for IBM 2400 bps modems ; ; This modem has a set of 8 switches on the rear panel. These ; switches should be set as follows: ; ; 1 2 3 4 5 6 7 8 ; ON X X X X X X X ; OFF X ; ; ; This script file contains the standard modem setup strings used ; by the External, Transmit and Listen programs. There are five ; procedures defined in this script file for setting up the modem and ; for connecting to a remote External machine. ; ; The modem setup strings used here will be adequate for most ; people but there may be some changes required if you are dialing ; overseas and require a longer wait for Carrier Detect (S7 register) ; or if you wish to change the speaker volume. Note that if you used ; the -Innn option in version 1.0 or 2.0 that you will have to modify ; the S7 register and recompile this script file. ; ; Consult your modem manual for more information on setup options. ; ; Script procedures defined: ; INITIALIZE ; RESET ; CALL ; ANSWER ; DISCONNECT ; ; Return codes for External, Transmit, Listen: ; 0 - OK ; 1 - CONNECT 300 ; 2 - not defined ; 3 - NO CARRIER ; 4 - ERROR ; 5 - CONNECT 1200 ; 6 - not defined ; 7 - BUSY ; 8 - NO ANSWER ; 9 - not defined ; 10 - CONNECT 2400 ; 11 - not defined ; 12 - CONNECT 9600 (high speed connection) ; ; ;********************************************************************* ; Special Notes Regarding the IBM 5853 Modem: ; ------------------------------------------- ; ; While the line is ringing (you can here it ring), this modem will ; not accept any modem commands, including "ATA", the command ; required to answer the phone. Commands can be issued to the modem ; only when the modem stops ringing completely, or when it is in ; between rings. ; ; "ATZ" cannot be issued safely between line rings, because this ; command would cause this modem to go off-hook and goes into data ; mode, and no further; modem commands are accepted until DTR is ; dropped, or 50 seconds later. ( The "ATZ" command would not reset ; the modem as well when the modem goes off-hook this way. The ; sequence "+++" would not bring the modem back to AT command mode ; either. ) INITIALIZE: title "IBM 2400bps modem Script" baud 2400 ; set the baud rate display " Baud Rate : 2400" $attempts = 5 init_retry: if (ri = 1) ; see if phone is ringing goto init_retry dtr 0 ; make sure modem is On-Hook wait 1 dtr 1 sendln "ATZ" ; reset modem to default settings wait 2 waitrsp 1 if ("0" isin response) goto reset_okay if ("OK" isin response) { reset_okay: if (ri = 1) ; see if phone is ringing goto reset_okay sendln "ATE0M1V0X1" wait 1 waitrsp 1 if ("0^M" isin response) { set_options: if (ri = 1) ; see if phone is ringing goto set_options sendln "ATS0=0S7=45S9=6S10=50S12=50" waitrsp 1 if (response = "0^M") return 0 } } dec $attempts if ($attempts > 0) goto init_retry return 4 RESET: baud 2400 ; set the baud rate display " Baud Rate : 2400" $attempts = 5 init_retry: if (ri = 1) ; see if phone is ringing goto init_retry dtr 0 ; make sure modem is On-Hook wait 1 dtr 1 sendln "ATZ" ; reset modem to default settings wait 2 waitrsp 1 if ("0" isin response) goto reset_okay if ("OK" isin response) { reset_okay: if (ri = 1) ; see if phone is ringing goto reset_okay sendln "ATE0M1V0X1" wait 1 waitrsp 1 if ("0^M" isin response) { set_options: if (ri = 1) ; see if phone is ringing goto set_options sendln "ATS0=0S7=45S9=6S10=50S12=50" waitrsp 1 if (response = "0^M") return 0 } } dec $attempts if ($attempts > 0) goto init_retry return 4 CALL: $ret = 8 ; set default ret code to "no answer" clearrsp ; clear the response buffer echo 0 ; do not display phone number sendln "ATD" + dial_mode + phone_number ; execute the dial up echo 1 ; turn echo back on waitrsp 120 ; wait up to 2 minutes for return code ; from modem if (response = "1^M") { baud 300 display ">>> CONNECT 300 <<<" $ret = 1 } else if (response = "3^M") { display ">>> NO CARRIER <<<" $ret = 8 ; no answer or no connect } else if (response = "5^M") { baud 1200 display ">>> CONNECT 1200 <<<" $ret = 5 } else if (response = "7^M") { display ">>> BUSY <<<" $ret = 7 ; busy } else if (response = "10^M") { baud 2400 display ">>> CONNECT 2400 <<<" $ret = 10 } else if (response = "25^M") { baud 1200 display ">>> CONNECT 1200/ECL <<<" $ret = 5 } else if (response = "30^M") { baud 2400 display ">>> CONNECT 2400/ECL <<<" $ret = 10 } return $ret ; return connect baud rate to ; application ANSWER: $ret = 8 ; set default ret code to "no answer" waitrsp 1 ; see if phone is ringing if ("2^M" isin response) ; 2 is numeric form of "RING" { answer_retry: if (ri = 1) ; if phone actually ringing at this ; moment goto answer_retry if (listen = 1) ; see if Listen program is running or sendln "ATD" ; not answer phone in originate mode ; (Listen) else sendln "ATA" ; answer the phone normally waitrsp 120 ; wait up to 2 minutes for return code ; from modem if (response = "1^M") { baud 300 display ">>> CONNECT 300 <<<" $ret = 1 } else if (response = "3^M") { display ">>> NO CARRIER <<<" $ret = 8 ; no answer or no connect } else if (response = "5^M") { baud 1200 display ">>> CONNECT 1200 <<<" $ret = 5 } else if (response = "10^M") { baud 2400 display ">>> CONNECT 2400 <<<" $ret = 10 } else if (response = "25^M") { baud 1200 display ">>> CONNECT 1200/ECL <<<" $ret = 5 } else if (response = "30^M") { baud 2400 display ">>> CONNECT 2400/ECL <<<" $ret = 10 } } return $ret ; return connect baud rate to ; application DISCONNECT: wait 2 ; wait 2 seconds send "+++" ; send escape sequence to put modem ; back to command state wait 2 ; wait 2 seconds clearrsp ; clear the response buffer sendln "ATH0" ; hang up the phone waitrsp 1 ; wait for a response if (response != "0^M") ; if hang up failed, drop DTR to force ; hang up { DTR 0 ; drop DTR to reset modem wait 2 ; some modems require a delay here DTR 1 ; raise DTR clearrsp ; clear response buffer } return 0 ; always return OK Additional query words: 2.10 2.1 2.10e ====================================================================== Keywords : Technology : kbMailSearch kbZNotKeyword3 kbMailPCN210e Version : WINDOWS:2.1e ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 1999.