DOCUMENT:Q109507 24-SEP-1999 [win3x] TITLE :README.WRI from Windows for Workgroups 3.11 (Part 2 of 4) PRODUCT :Microsoft Windows 3.x Retail Product PROD/VER:WINDOWS:3.11 OPER/SYS: KEYWORDS: ====================================================================== ------------------------------------------------------------------------------- The information in this article applies to: - Microsoft Windows for Workgroups version 3.11 ------------------------------------------------------------------------------- SUMMARY ======= The following information was taken from the Microsoft Windows for Workgroups version 3.11 README.WRI file. MORE INFORMATION ================ 6.0 Using SMARTDrive Version 5.0 This section describes some solutions to problems that you might encounter when using SMARTDrive version 5.0 (provided with Windows for Workgroups) with specific applications or hardware. 6.1 Accessing Floppy Disk Drives on Older COMPAQ DESKPROS On some COMPAQ DESKPRO 386/16 and 386/20 computers, you might experience problems accessing floppy disk drives when SMARTDrive version 5.0 is installed. To work around the problem, you can try one of the following solutions: - Place the SMARTDrive buffer into low memory by adding the following option to the smartdrv command line in your AUTOEXEC.BAT file: smartdrv /L - Disable the caching on floppy disk drives by adding the following options to the smartdrv command line in your AUTOEXEC.BAT file: smartdrv a- b- For more information about these options, see "Managing Memory and Performance" in your Windows or Windows for Workgroups user's guide. 6.2 Using SMARTDrive with Double Buffering Most expanded-memory emulators attempt to optimize SMARTDrive by configuring it to load into upper memory blocks (UMBs). This will cause problems if you are running Windows for Workgroups with double buffering. If you need to use double buffering with SMARTDrive, make sure that SMARTDrive is configured to load into low memory. The SMARTDrive command line in your CONFIG.SYS file should look like this: device=smartdrv.exe /double_buffer You do not need to change the references to SMARTDrive in your AUTOEXEC.BAT file. If you're using a SCSI device, some vendors provide a driver (such as ASPI4DOS) that supplies double-buffering already. You should not use SMARTDrive double-buffering in this case. Check your SCSI device documentation, or contact your SCSI device vendor to determine whether your driver has its own double-buffering. If it does, use the following command line: device=smartdrv.exe /double_buffer+ This command line should also be used if your system hangs when starting Windows, or if you are using a SCSI drive with a UNIX partition. For more information about using double buffering with SMARTDrive, see "Managing Memory and Performance" in your Windows or Windows for Workgroups user's guide. 6.3 Using SMARTDrive with Norton Utilities Version 6.0 Disk Monitor Do not use the Disk Protect feature in Norton Utilities Version 6.0 Disk Monitor with SMARTDrive version 5.0. If you try to write to the protected drive, you will encounter an error and your system will fail. If you want to write to and cache a protected drive, add the drive letter to the smartdrv command line in your AUTOEXEC.BAT file. For example, if drive D is a protected drive, you would add the following: smartdrv d Or you can use the Norton cache program instead of SMARTDrive when you are using Disk Monitor. 6.4 Using SMARTDrive with SuperStor Disk-Compression Utility - Do not use the Create Mountable Drive, Mount, and Dismount features of SuperStor after SMARTDrive is loaded. You must configure your SuperStor partitions before loading SMARTDrive. Windows for Workgroups Setup places the smartdrv command line first in your AUTOEXEC.BAT file. If your AUTOEXEC.BAT file includes "mount" configuration commands, make sure that the smartdrv command line follows the SuperStor configuration command lines. - Also, you will receive read-write errors if you use SMARTDrive to cache a SuperStor compressed drive. To prevent SMARTDrive from caching the compressed drive, you must include the drive letter- option on the smartdrv command line. For example, if drive C is the uncompressed drive, and drives E and F are the compressed SuperStor drives, you would include the following command line in your AUTOEXEC.BAT file: smartdrv e- f- 6.5 Using SMARTDrive with Copy-Protected Games and Applications When using SMARTDrive, you may encounter problems starting a copy-protected application that requires you to place the master disk in the floppy disk drive. To solve this problem, you need to disable caching on the floppy disk drive by using the drive letter- option when you load SMARTDrive. For example, if you load SMARTDrive from your AUTOEXEC.BAT file and you are using drive A, you need to include the following command line in your AUTOEXEC.BAT file: smartdrv a- 7.0 Using Multimedia Extensions Version 1.0 with Windows for Workgroups This section covers information that is specific to using the Multimedia Extensions version 1.0 with Windows for Workgroups. It also covers additional tasks you need to perform to configure your system properly for use with the Multimedia Extensions. 7.1 Upgrading to Windows for Workgroups To use the Multimedia Extensions with Windows for Workgroups, first set up Windows with Multimedia Extensions version 1.0. Then upgrade to Windows for Workgroups by installing it into the same directory. If you set up Windows for Workgroups before setting up Multimedia Extensions, not all the files will be properly installed. 7.2 Configuring MIDI Setups When you set up Windows for Workgroups, Setup does not overwrite an existing Multimedia Extensions MIDI-setup file MIDIMAP.CFG. If the port settings in your original setups refer to the Ad Lib or Sound Blaster ports and you are using different drivers, then you need to change the port settings to match the output ports used by your sound device. To do this, use the MIDI Mapper option in Control Panel. For more information about using MIDI Mapper to modify MIDI setups, see "Customizing Windows" or "Customizing Windows for Workgroups" in your Windows or Windows for Workgroups user's guide. 7.3 Configuring Your Display The Multimedia Extensions Display icon in Control Panel is not available when you upgrade from Windows with Multimedia version 1.0 to Windows for Workgroups. If you need to change options for your display, run Windows Setup from the Main group in Program Manager to make these changes. 7.4 Sample MIDI File The sample MIDI file CANYON.MID included with Windows for Workgroups, which you can play with Windows Media Player, is provided by Passport Designs, Inc. 7.5 Using HyperGuide The information in HyperGuide refers to Windows version 3.0, not Windows for Workgroups. If you need to use Windows documentation, see the Microsoft Workgroup Add-on "User's Guide" that comes with Windows for Workgroups. 7.6 Using Music Box Music Box is not fully compatible with Windows for Workgroups. Although your compact discs will play correctly, you will encounter problems when using the Save Info button in the Program dialog box to save disc-title and track-title information. If you want to modify this information, you must do so manually by editing the MUSICBOX.INI file. To add a new disc to the file, you can determine the disc ID number by viewing the information in the About dialog box. 7.7 Using Alarm Clock The Alarm Clock in the Multimedia Extensions version 1.0 is not fully compatible with Windows for Workgroups. If you are using the digital display, the time may appear slanted or a system error may occur, depending on the size of the Alarm Clock window. 8.0 Running Specific MS-DOS-Based Applications This section provides information about running specific MS-DOS-based applications with Windows for Workgroups. 8.1 Creative Labs JukeBox If you are using a Sound Blaster sound card, do not set up or use the JukeBox application included in your Sound Blaster package with Windows for Workgroups. JukeBox interferes with the Windows for Workgroups driver for the Ad Lib synthesizer and causes errors when you try to install the drivers for the Sound Blaster card. 8.2 Games or Timing-Sensitive Applications Some games or applications that rely on the computer's timer may perform poorly in Windows for Workgroups. You can try increasing the performance by turning off the TrapTimerPorts setting in the [386Enh] section of the SYSTEM.INI file, as follows: TrapTimerPorts=OFF Note: The TrapTimerPorts setting is on by default. Turning it off may cause errors or a loss of data when you transfer files by using a communications application. It is recommended that you leave this setting turned on when using a communications application. 8.3 Third-Party Expanded-Memory Emulators with MS-DOS Version 5.0 and 6.0 Many expanded-memory emulators will cause problems if you use them to provide upper memory blocks (UMBs) for the MS-DOS version 5.0 or 6.0 loadhigh and devicehigh commands. If you want to use these MS-DOS commands to load drivers or applications high, use the Windows EMM386.EXE expanded-memory emulator to provide UMBs instead. If you must use a third-party expanded-memory emulator, use the load high feature provided with the emulator instead of using the MS-DOS commands. 8.4 PC Tools Applications If you run a PC Tools MS-DOS-based application in a window, the display might be garbled, because PC Tools applications use a graphics font that is not displayed correctly. (This problem does not occur if you run the application in a full screen). To correct the problem, start your PC Tools MS-DOS-based applications by using the /NF option. If these applications are included in a Program Manager group, use the Properties command to add the /NF option to the command line for each application. For more information about changing application properties, see Help for Program Manager. You can also include the /NF option in the application's program information file (PIF) by typing it in the Optional Parameters text box in PIF Editor, or you can use the PC Tools PC Config program to specify that PC Tools applications should use the Text Font to display information. For more information about changing an application's PIF, see your Windows or Windows for Workgroups user's guide. 8.5 WordPerfect Version 5.1 When you run WordPerfect version 5.1 in a window, the Windows mouse pointer and the WordPerfect mouse pointer do not appear in the same place. To fix this problem, carry out the following procedure. 1. In WordPerfect, press SHIFT+F1. 2. Press M for Mouse and A for Acceleration Factor. 3. Set the Acceleration Factor to 1. 4. Press ENTER three times to return to your document. 5. Enlarge the WordPerfect window to fill the entire screen. 6. Move the Windows mouse pointer into the WordPerfect window, and then move it to the far-right edge of the window. 7. Move the mouse pointer to the far-left edge of the window. 8. Move the pointer back to the center of the window, and then move it down to the bottom edge. 9. Finally, move the pointer up to the upper-left corner of the window. The Windows mouse pointer and the WordPerfect mouse pointer should now be in the same location. 8.6 3270-Emulation Applications You may encounter problems using certain 3270-emulation applications with Windows for Workgroups. If you are using one of these applications, it is recommended that you purchase the Microsoft Windows for Workgroups Resource Kit (Version 3.1). For information about ordering the resource kits, see section 17 in this file. 8.7 C/C++ Version 7.0 If you are running Microsoft C/C++ Version 7.0 with Windows for Workgroups and your system locks up when compiling a file, add the following line to the [386Enh] section of your SYSTEM.INI file: MAXBPS=400 This command increases the number of breakpoints the system uses. For more information about this setting, see the Microsoft Windows for Workgroups Resource Kit (Version 3.1). For information about ordering resource kits, see section 17 of this file. 9.0 Running Communications Applications This section provides information on using communications applications with Windows for Workgroups. 9.1 General Guidelines The maximum bit rate possible when running your communications program with Windows is determined by your CPU speed in addition to your port and modem capabilities. RTS/CTS or hardware handshaking may also be required. To communicate at 9600 bits per second (BPS) or faster, follow these guidelines: - Use Windows-based communications applications when possible. - Use 16550AF-compatible serial ports and modems. To determine if your serial port is 16550AF-compatible, you can run the Microsoft Diagnostics program (MSD.EXE) included with Windows for Workgroups. To run MSD, quit Windows, and then type msd at the command prompt (not from an MS-DOS prompt within Windows). Then press ENTER. - Avoid closing MS-DOS-based applications during a background download. - Use a PIF file to run MS-DOS-based communications applications. Use the PIF Editor to select the "Background Execution" and "Lock Application Memory" check boxes. - When you are running an MS-DOS-based communications application in the background, reduce it to an icon rather than running it in a window. - SMARTDrive may cause download errors when it clears the write-behind cache. If this happens, disable the SMARTDrive write-behind cache during high-speed downloads. This can be done easily using the SmartMon utility included in the Microsoft Windows for Workgroups Resource Kit (Version 3.1), and in MS-DOS 6.0. For information about ordering resource kits, see section 17 of this file. 9.2 Using an Intel CAS Modem with 32-Bit File Access You cannot use an Intel CAS modem with 32-bit file access. If you are using an Intel CAS modem, from Control Panel, select the 386 Enhanced icon, choose the Virtual Memory button, and then choose the Change button. Make sure the Use 32-Bit File Access check box is not checked, and select OK. If it was checked, you must exit and restart Windows. 10.0 Using Specific Display Adapters with Windows for Workgroups This section describes some problems you might encounter when you use specific display adapters or drivers with Windows for Workgroups. 10.1 Installing Display Adapters by Following the Manufacturer's Instructions The installation procedures that are provided by display-adapter manufacturers may require you to replace or modify the SETUP.INF file in the Windows SYSTEM directory. This will cause problems in Windows for Workgroups. If your third-party display-adapter installation replaces or modifies the SETUP.INF file, use the following procedure instead. To install the display-adapter drivers: 1. Rename the SETUP.INF file provided with your display-adapter package to OEMSETUP.INF, and place it on the disk or in the directory containing the third-party display-driver files. 2. From the Main group, run Windows Setup. 3. Choose Change System Settings from the Options menu. 4. From the list of Display options, choose Other Display (Requires disk from OEM). 5. Insert the disk that contains the OEMSETUP.INF file and the driver files for your display adapter. Or, if these files are located on your hard disk, type the path to the directory that contains the files, and then choose the OK button. 6. Select the type of display adapter you want to use, and then choose the OK button. Setup copies all necessary files from the driver disk and may request files from the Windows for Workgroups disks. 7. Insert any additional disks that are requested, and then choose the OK button. If you accidentally overwrite the original SETUP.INF file, you can copy it from Windows for Workgroups version 3.11 Disk 1 back into your Windows SYSTEM directory. Additional query words: wfw wfwg 3.11 ====================================================================== Keywords : Technology : kbAudDeveloper kbWFWSearch kbWFW311 Version : WINDOWS:3.11 ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 1999.