DOCUMENT:Q68128 18-SEP-1999 [win3x] TITLE :Troubleshooting the CONFIG.SYS and AUTOEXEC.BAT Files PRODUCT :Microsoft Windows 3.x Retail Product PROD/VER:WINDOWS:3.0,3.0a,3.1,3.11 OPER/SYS: KEYWORDS:win31 ====================================================================== 3.00 3.00a 3.10 3.11 WINDOWS kbfasttip kbtshoot ------------------------------------------------------------------------------- The information in this article applies to: - Microsoft Windows versions 3.0, 3.0a, 3.1, 3.11 ------------------------------------------------------------------------------- SYMPTOMS ======== When you run or install Microsoft Windows, you may encounter the following problems: corrupted or incomplete installation of Windows, insufficient memory or file handles, and/or an inability to use standard and enhanced modes of Windows. CAUSE ===== Your CONFIG.SYS and AUTOEXEC.BAT files contain device drivers, terminate-and-stay-resident (TSR) programs, and other files. WORKAROUND ========== To reduce or eliminate these problems, follow the instructions in the More Information section of this article to modify the CONFIG.SYS and AUTOEXEC.BAT files. Use a text editor such as MS-DOS EDIT, EDLIN programs, or Windows Notepad to edit your CONFIG.SYS and AUTOEXEC.BAT files. NOTE: Make backup copies of the the AUTOEXEC.BAT and CONFIG.SYS files, before you make your changes. MORE INFORMATION ================ CONFIG.SYS File --------------- Modify the CONFIG.SYS file as follows: 1. Remove nonessential device drivers such as keyboard buffers, scanner drivers, printer drivers, and country drivers. If you are unsure of what a device driver does, do NOT remove it. 2. Remove FASTOPEN statements and disk caches. 3. Verify that you have at least 60 FILES, and 20 BUFFERS. 4. If you are using MS-DOS version 3.3 or later, add a STACKS=0,0 line to your CONFIG.SYS file. For MS-DOS version 3.2, the line should read STACKS=9,192. For more information on STACKS, query on the following words in the Microsoft Knowledge Base: stacks and explanation and config 5. If you have a SHELL=COMMAND.COM /P /E:256 statement, increase the number following the E: (the environment space) to 2048. Verify that the /p switch is used. If you do not have a SHELL command, you may want to add one, making sure that the path to COMMAND.COM in the SHELL statement matches the COMSPEC statement. At the command prompt, type set This command will give you the path to which the location COMSPEC is pointing. AUTOEXEC.BAT File ----------------- Modify the AUTOEXEC.BAT file as follows: 1. Remove any nonessential programs such as TSR programs, print buffers and APPEND, JOIN, SUBST, PRINT, and GRAPHICS statements. If you are unsure of what a program does, do NOT remove it. 2. Remove all duplicate PATH entries so you only have one PATH line in your AUTOEXEC.BAT file. Modify your PATH statement so it uses the root, MS-DOS, and Windows directories only. 3. Verify that you have a valid SET TEMP statement to an existing directory. For example, SET TEMP=C:\WINDOWS\TEMP. Additional Troubleshooting Steps -------------------------------- - Verify that the File Allocation Table is valid: 1. Exit Windows. 2. At the command prompt, type the following: chkdsk /f Caution: You must Exit Windows BEFORE you type the above command. CHKDSK will also check the directory structure. - Verify that you are using the proper version of DOS for your computer. For example, if you are using a COMPAQ computer, you should be using a version of COMPAQ DOS. - Verify that the path, environment space, and TEMP directory are valid. At the command prompt, type: set Reinstall Windows after you make the above changes to the CONFIG.SYS and AUTOEXEC.BAT files. NOTE: Before you reinstall Windows, switch your computer off, wait a few seconds, and switch your computer on again and read the new CONFIG.SYS and AUTOEXEC.BAT files to verify your changes. - To determine the function of certain drivers when Windows will not run, create a MS-DOS boot floppy disk containing the following CONFIG.SYS file and AUTOEXEC.BAT files and boot from the floppy disk. CONFIG.SYS: AUTOEXEC.BAT: FILES=50 PATH=C:\WINDOWS;C:\DOS BUFFERS=20 PROMPT $P$G DEVICE=C:\HIMEM.SYS SET TEMP=C:\WINDOWS\TEMP If, after booting, you can access the hard disk properly (CHKDSK gives the same output as before) try to run Windows. If CHKDSK gives different output, do NOT run CHKDSK /F in this state. You may have booted without a driver necessary to access the hard drive properly. Remove the floppy and reboot from the hard drive. For more information on troubleshooting similar Windows problems, query on the following word in the Microsoft Knowledge Base: tshoot REFERENCES ========== "Getting Started with Microsoft Windows," version 3.1, page 100 "Microsoft Windows User's Guide," version 3.0, page 515 Additional query words: 3.00 3.00a 3.10 3.11 clean boot ====================================================================== Keywords : win31 Technology : kbWin3xSearch kbZNotKeyword3 kbWin300 kbWin300a kbWin310 kbWin311 Version : WINDOWS:3.0,3.0a,3.1,3.11 ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 1999.