Adaptec 1542b Err Msg: Inaccessible Boot Device

Last reviewed: May 13, 1997
Article ID: Q108239

The information in this article applies to:
  • Microsoft Windows NT operating system version 3.1
  • Microsoft Windows NT Advanced Server version 3.1

SYMPTOMS

The drive your computer boots from is connecting to an Adaptec 1542b SCSI controller. During Windows NT Setup, the following STOP message appears:

   Inaccessible boot device

CAUSE

This STOP message may have been caused by an incorrect jumper setting on the Adaptec adapter for either the IRQ or DMA speed.

RESOLUTION

Set the jumpers on the Adaptec adapter to their defaults and make sure no other adapters are using the same IRQ levels or base I/O addresses. It is important that the IRQ specified on jumpers 9 through 11 in jumper block 5 is the same as the IRQ specified in jumper block 9. It is also important that the DMA speed, specified by jumper 12 in jumper block 5, be set to 5.7.

Jumper Settings

Jumper Block 5:

   SCSI Parity (default = enabled)
   JP5.3 = ON

   SCSI ID (default = 7)
   JB5.4 = OFF
   JB5.5 = OFF
   JB5.6 = OFF

   DMA Channel (default = 5)
   JB5.7 = OFF
   JB5.8 = ON

   IRQ (default = 11)
   JB5.9 = OFF
   JB5.10 = ON
   JB5.11 = OFF

   DMA SPEED (default = 5.7)
   JB5.12 = ON
   JB5.13 = OFF

Jumper Block 6 - BIOS AutoSense Control:

   JB6.1 = ON

Jumper Block 7 - Address Selection:

   I/O Address (default = 0x330)
   JB7.2 = ON
   JB7.3 = OFF
   JB7.4 = OFF

   BIOS Wait State Select (default = 0)
   JB7.5 = OFF
   JB7.6 = OFF

   BIOS Base Address (default = 0xDC000)
   JB7.7 = OFF
   JB7.8 = OFF

Jumper Block 8 - Floppy Disk:

   Floppy (default = enabled)
   JB8.1 = ON

   DMA Request (default = 2)
   JB8.2 = ON
   JB8.3 = OFF

   DMA Ack (default = 2)
   JB8.4 = ON
   JB8.5 = OFF

   IRQ (default = 6)
   JB8.6 = ON

Jumper Block 9 - DMA / IRQ Selection:

   DMA Request (default = 5)
   JB9.1  = OFF
   JB9.2  = ON
   JB9.3  = OFF
   JB9.4  = OFF

   DMA Ack (default = 5)
   JB9.5  = OFF
   JB9.6  = ON
   JB9.7  = OFF
   JB9.8  = OFF

   IRQ Request (default = 11)
   JB9.9  = OFF
   JB9.10 = OFF
   JB9.11 = ON
   JB9.12 = OFF
   JB9.13 = OFF
   JB9.14 = OFF

The Adaptec product included here is manufactured by a vendor independent of Microsoft; we make no warranty, implied or otherwise, regarding this product's performance or reliability.


Additional query words: prodnt blue trap
Keywords : kbhw kbsetup nthw ntsetup ntstop
Version : 3.1
Platform : WINDOWS
Issue type : kberrmsg


THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY.

Last reviewed: May 13, 1997
© 1998 Microsoft Corporation. All rights reserved. Terms of Use.