DOCUMENT:Q155407  08-AUG-2001  [winnt]
TITLE   :Setting Up Windows NT on Motorola PowerStack When Drive Is New
PRODUCT :Microsoft Windows NT
PROD/VER:winnt:4.0
OPER/SYS:
KEYWORDS:kb3rdparty kbsetup

======================================================================
-------------------------------------------------------------------------------
The information in this article applies to:

 - Microsoft Windows NT Workstation version 4.0 
 - Microsoft Windows NT Server version 4.0 
-------------------------------------------------------------------------------

SUMMARY
=======

This article describes the steps necessary to install Windows NT on a Motorola
PowerStack computer, when the drive is new or has been low-level formatted. When
all boot information on the drive is missing, the system will display the
following information when the computer is started:

   AutoBoot about to begin.. Press <ESC> to Bypass, <SPC> to Continue
   Scanning System for Attached Mass Storage Devices
   Attempting BOOT from Device(s) of Type = FDISK
   Attempting BOOT from Device(s) of Type = CDROM
   Attempting BOOT from Device(s) of Type = TAPE
   Attempting BOOT from Device(s) of Type = HDISK

   Autoboot Failed
   PPC1-Diag>

If your computer is in this state, follow the instructions below.

MORE INFORMATION
================

The following materials must be available before beginning:

 - PPC Boot Disk (Available from Motorola)

 - Arcinst.exe (Available from Motorola)

 - FW.IMG on disk (Available from Motorola)

 - Windows NT compact disc (Available from Microsoft)

1. Start the computer from the PPC boot disk.

2. When the firmware loads:

   a. Insert the disk that has Arcinst.exe in the floppy disk drive.

   b. Select Run a Program.

   c. In Program to Run type the following:

      a:\arcinst

   d. Press Enter.

3. Select Configure Partitions.

4. Select Create PowerPC Boot Partition. If more than one SCSI bus is available,
   select the appropriate SCSI bus. You will receive the following message:

   Partition successfully created.
   Press any key to continue...

   The partition will be automatically formatted. Then the following message will
   be displayed:

   Partition formatted successfully.
   Press any key to continue

5. Press a key; the following prompt is shown:

   Enter pathname for the PowerPC BootLoader:

   Insert the disk with the correct Fw.img file into the floppy disk drive and
   type:

   a:\fw.img

   The following messages will be shown:

   Reading ARC from:
   multi(1)disk(0)fdisk(0)\fw.img
   Load Image Size = 288000
   Press any key to continue...

   Boot Software Copied Successfully.
   Press any key to continue...

   Successfully installed PowerPC Boot Loader.

6. On the ARCINST menu select Create Partition. If required, select the
   appropriate SCSI bus.

7. At the "Enter the size in MB (1-1000):" prompt, type the size for the system
   partition; this will typically be 10 MB. The following message is displayed:

   Partition successfully created.
   Press any key to continue...

   You will get this prompt:

   Do you want to make this the system partition (y/n)?

   Type 'y' (without quotation marks) and press ENTER. The partition will be
   automatically formatted. The "Partition formatted successfully" message will
   be displayed again. Press any key to continue.

8. Quit ARCINST.

9. On the firmware menu, select the "Run a program" option and type:

   cd:\ppc\setupldr

10. Windows NT Setup will start. Setup can be used to partition the remainder of
   the drive and install a new copy of Windows NT.


The third-party products discussed here are manufactured by vendors independent
of Microsoft; we make no warranty, implied or otherwise, regarding these
products' performance or reliability.

Additional query words:

======================================================================
Keywords          : kb3rdparty kbsetup 
Technology        : kbWinNTsearch kbWinNTWsearch kbWinNTW400 kbWinNTW400search kbWinNT400search kbWinNTSsearch kbWinNTS400search kbWinNTS400
Version           : winnt:4.0

=============================================================================

THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS
PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND.  MICROSOFT DISCLAIMS
ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  IN NO
EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR
ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF
MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.  SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES
SO THE FOREGOING LIMITATION MAY NOT APPLY.

Copyright Microsoft Corporation 2001.