DOCUMENT:Q49717  17-DEC-2000  [msdos]
TITLE   :Using MS-DOS Shell to Format Low-Density Disks
PRODUCT :Microsoft Disk Operating System
PROD/VER:MS-DOS:4.x,5.x,6.0,6.2,6.21,6.22
OPER/SYS:
KEYWORDS:

======================================================================
-------------------------------------------------------------------------------
The information in this article applies to:

 - Microsoft MS-DOS operating system versions 4.0, 4.01, 5.0, 5.0a, 6.0, 6.2, 6.21, 6.22 
-------------------------------------------------------------------------------

SUMMARY
=======

The MS-DOS Shell's "DOS Utilities" title list contains a FORMAT command. If you
select this utility, the MS-DOS Shell displays a dialog box and a default
parameter, of "a:". This is documented on Page 33 of the "Microsoft MS-DOS Shell
User's Guide" manual for version 4.0.

If you have a high-density drive (that is, 5.25-inch 1.2 MB or 3.5-inch 1.44 MB)
and high-density floppies, you should just press the ENTER key. If you have a
low-density drive, this is not a concern because only low- density disks can be
used. You just need to be careful within the MS-DOS Shell or at the command line
when using low-density disks in a high-density drive. You usually won't need to
change the default of "a:".

In the above situation, you must add to the "a:" default an extra parameter to
format low-density disks in a high-density drive. For 5.25-inch 360K disks, the
parameter is /F:360K. For 3.5-inch 720K disks, the parameter is /F:720K. This
makes the dialog box display either "a: /F:360K" or "a: /F:720K", depending on
disk size.

Changing parameters in a dialog box is often forgotten while using the MS-DOS
Shell, since the MS-DOS Shell allows you to point and click without typing, and
in many cases without any need for documentation.

MORE INFORMATION
================

If you have a high-density disk drive and format both low-density and high-
density disks in the drive, you can avoid this problem by adding a program with
a title similar to "Format low density" that would format a disk with the "/4"
option.

The default MS-DOS Shell command definition for the FORMAT command is as
follows:

   format [/t"Format Utility"/i"Enter drive to Format."/p
          "Parameters . .  "/d"a: "/r]||pause||

The line above has been split immediately following the "/p" parameter, but
should fit on one line. The ||'s above are generated with the F4 key.

To make a "Format low density" program entry, just copy the entry to a new entry,
change the program name, then change the program's command options. The string
in quotation marks following "/t" can be changed to "Format low density
Utility", and the string following "/d" can be changed to "a: /F:360K" or "a:
/F:720K", depending on disk size.

Additional query words: 4.00 4.01 5.00 5.00a 6.00 6.20 6.21 6.22 Dosshell

======================================================================
Keywords          :  
Technology        : kbMSDOSSearch kbMSDOS400 kbMSDOS621 kbMSDOS622 kbMSDOS620 kbMSDOS600 kbMSDOS500 kbMSDOS401 kbMSDOS500a
Version           : MS-DOS:4.x,5.x,6.0,6.2,6.21,6.22

=============================================================================

THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS
PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND.  MICROSOFT DISCLAIMS
ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  IN NO
EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR
ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF
MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.  SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES
SO THE FOREGOING LIMITATION MAY NOT APPLY.

Copyright Microsoft Corporation 2000.