DOCUMENT:Q60713 17-DEC-2000 [msdos] TITLE :Common RESTORE Problems, Including "No Files Found to Restore" PRODUCT :Microsoft Disk Operating System PROD/VER:MS-DOS:3.x,4.x,5.x,6.0,6.2,6.21,6.22 OPER/SYS: KEYWORDS:msdos ====================================================================== ------------------------------------------------------------------------------- The information in this article applies to: - Microsoft MS-DOS operating system versions 3.1, 3.2, 3.21, 3.3, 3.3a, 4.0, 4.01, 5.0, 5.0a, 6.0, 6.2, 6.21, 6.22 ------------------------------------------------------------------------------- SUMMARY ======= The MS-DOS RESTORE command expects a full target file specification, including the exact filename or wildcard. If the target file(s) to be RESTOREd are not fully specified, RESTORE reads all of the BACKUP disks and display the following message: Warning! No files found to restore. For example, to RESTORE all files backed up from the C:\TEST directory, use the following command: restore a: c:\test\*.* To RESTORE all files that are backed up, use the following command: restore a: c:\*.* /s The RESTORE command places the files in the same directory that they were backed up from, creating directories as needed. MORE INFORMATION ================ Listed below are a few points you should keep in mind when using the BACKUP and RESTORE commands: - You must RESTORE to the same path that you specified (either implicitly or explicitly) when you used BACKUP. You can RESTORE to a different drive. - The files created by the version of BACKUP that comes with MS-DOS versions 3.3 and later are different from those created by earlier versions of BACKUP. You can determine which version of BACKUP was used by looking at the output of a DIR command on your BACKUP disk. Versions of BACKUP earlier than version 3.3 produce files similar to the following: BACKUPID.@@@ TEST1.BAR TEST2.BAR ... TESTn.BAR The version of BACKUP that comes with MS-DOS versions 3.3 and later produces the following files only (where x signifies the disk number in the backup sequence): BACKUP.00x CONTROL.00x - The version of RESTORE that comes with MS-DOS version 3.3 RESTOREs backup files created with earlier versions of BACKUP, except for backup files created with MS-DOS version 3.2. (Backup files created with IBM PC-DOS 3.2 are different from those created with MS-DOS 3.2, and can be restored with MS-DOS versions 3.3 and later). Backup files created with MS-DOS 3.2 must: Be RESTOREd with MS-DOS 3.2, MS-DOS 3.21, or MS-DOS 5.0. - The version of RESTORE included with MS-DOS 6.0 and 6.2 restores backup files created with MS-DOS 2.0 through 5.x. To restore backup files created with MS-DOS 6.0 and 6.2, use the MSBACKUP program. - RESTORE expects a full file specification in all cases. The command: restore a: c:\test causes RESTORE to search the backup disks for a file backed up from the root directory called TEST, ignoring any files that were backed up from the \TEST subdirectory. BACKUP, however, is different. The command backup c:\test a: causes BACKUP to attempt to back up the file C:\TEST; but if that file does not exist, BACKUP attempts to back up C:\TEST\*.*. Thus, the command backup c:\test a: backs up the contents of the directory C:\TEST to a floppy; but the command: restore a: c:\test does not restore that directory; instead, the following message is displayed: Warning! No files found to restore To RESTORE a directory called TEST, the file(s) to be restored must be included as well, as in the following: restore a: c:\test\*.* NOTE: For MS-DOS versions 3.1-3.21, when RESTOREing a subdirectory that was previously backed up, you do not need to specify a filename with the path IF the intended directory is already present on the target drive. If the subdirectory you intend to RESTORE does not exist, RESTORE always fails with the "No files found to restore" message. Again, you need to specify a full filename. Additional query words: appnote 3.10 3.20 3.21 3.30 3.30a 4.00 4.01 5.00 6.00 6.20 ====================================================================== Keywords : msdos Technology : kbMSDOSSearch kbMSDOS321 kbMSDOS400 kbMSDOS320 kbMSDOS330a kbMSDOS621 kbMSDOS622 kbMSDOS620 kbMSDOS600 kbMSDOS310 kbMSDOS500 kbMSDOS330 kbMSDOS401 kbMSDOS500a Version : MS-DOS:3.x,4.x,5.x,6.0,6.2,6.21,6.22 ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 2000.