DOCUMENT:Q72016 03-DEC-1999 [msdos] TITLE :Loading Networks into UMBs with MS-DOS 5.0 PRODUCT :Microsoft Disk Operating System PROD/VER:MS-DOS:5.0 OPER/SYS: KEYWORDS: ====================================================================== ------------------------------------------------------------------------------- The information in this article applies to: - Microsoft MS-DOS operating system version 5.0 ------------------------------------------------------------------------------- SUMMARY ======= Network programs tend to use a lot of lower memory. If you have sufficient space for the programs in UMBs (upper memory blocks), you can achieve substantial memory savings. The following sections describe how to load some of the major networks into UMBs. If your network is not listed here, please contact your network vendor for information on how to load the network into a UMB. NOTE: It is assumed in all of the following sections that you have read the "Running Programs in the Upper Memory Area" section in the version 5.0 "Microsoft MS-DOS User's Guide and Reference." MORE INFORMATION ================ MS-NET Based Networks --------------------- Most MS-NET based redirectors are loaded with the NET command. Look in your AUTOEXEC.BAT file (or other file that you use to start the network) for a command similar to the following: net start where is other text following START. Add the word LOADHIGH to the beginning of the line, as follows: loadhigh net start Reboot your computer and check to make sure that the network loads without problems. You can use the MEM command to see how much memory you now have available. LAN Manager 1.x/2.x Based Redirectors ------------------------------------- These redirectors are of two types: basic and enhanced. If you start the network with the command "NET START WORKSTATION," you are running the enhanced version. If you start the redirector with a command similar to "NET START RDR," you are running the basic version. Look in your AUTOEXEC.BAT file (or other file that you use to start the network) to see which command is used. LAN Manager 1.x/2.x Basic Redirectors ------------------------------------- These redirectors will often fit into a UMB. To load them high, add the word LOADHIGH before the NET START command: loadhigh net start Reboot your computer and check to make sure that the network loads without problems. You can use the MEM command to see how much memory you now have available. LAN Manager 1.x/2.x Enhanced Redirectors ---------------------------------------- Best memory savings with LAN Manager enhanced redirectors (versions 2.0b and earlier) is achieved by instructing the network to use LIM memory. 1. Use the RAM option on EMM386 to specify that both UMB and EMS memory be provided. For example, if the line to load EMM386.EXE is device=c:\dos\emm386.exe 1024 then change the line to the following: device=c:\dos\emm386.exe 1024 ram 2. Locate the LANMAN.INI file by typing the following at the MS-DOS prompt: " c: cd \ dir /s /b lanman.ini " (without the quotation marks) If more than one LANMAN.INI file is found, use the one that appears first in the PATH (use the PATH command to see the path). 3. Edit the LANMAN.INI file. For example, if the file is in C:\LM.DOS, then use the following command: edit c:\lm.dos\lanman.ini This command invokes the MS-DOS Editor. 4. Use the SEARCH command to find the LIM option (ALT+S means hold down the ALT key while pressing S): " ALT+S F " (without the quotation marks) A dialog box asking to "Find What" will be displayed. Type "LIM" (without the quotation marks) and press ENTER. 5. If the line has a semicolon (;) at the beginning, remove the semicolon. Ensure that the line now reads: lim = yes LAN Manager 2.0c ---------------- Microsoft LAN Manager version 2.0c is the first version of LAN Manager with the ability to load itself high with Microsoft MS-DOS version 5.0. The LAN Manager 2.0c redirector is loaded high automatically if there is enough room in the upper memory area (UMA). Other network services can be loaded high using the MS-DOS LOADHIGH (LH) command. Loading Novell Networks into UMBs --------------------------------- When you start your network, specify LOADHIGH before the Novell startup command. For example, if you are using NET5.EXE to start Novell, add LOADHIGH before NET5. REFERENCES ========== "Microsoft MS-DOS User's Guide and Reference," version 5.0 "Microsoft MS-DOS Getting Started," version 5.0 The Novell products included here are manufactured by a vendor independent of Microsoft; we make no warranty, implied or otherwise, regarding these products' performance or reliability. Additional query words: 2.00b 2.00c 5.00 ====================================================================== Keywords : Technology : kbMSDOSSearch kbMSDOS500 Version : MS-DOS:5.0 ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 1999.