DOCUMENT:Q76996  26-NOV-1999  [msdos]
TITLE   :Creating Backup Disks of the MS-DOS 5 Upgrade
PRODUCT :Microsoft Disk Operating System
PROD/VER:MS-DOS:5.0
OPER/SYS:
KEYWORDS:

======================================================================
-------------------------------------------------------------------------------
The information in this article applies to:

 - Microsoft MS-DOS operating system version 5.0 
-------------------------------------------------------------------------------

SUMMARY
=======

This article outlines the steps for creating backup copies of the MS-DOS 5
Upgrade disks.

The upgrade disks are shipped in two formats:

 - Six 360K 5.25-inch disks

 - Three 720K 3.5-inch disks

Per the Microsoft Software Licensing Agreement, one copy of the MS-DOS 5 Upgrade
is required for each computer on which it is installed.

MORE INFORMATION
================

To Back Up 5.25-inch Disks to 5.25-inch Disks
---------------------------------------------

Six 5.25-inch blank disks (formatted or unformatted) are required for this
procedure.

1. Boot the computer with the current version of DOS.

2. Insert disk 1 in drive A.

3. Insert blank disk in drive B (if two 5.25-inch floppy disk drives are
   available).

4. Move to the C: drive root directory (C:\>), or to the directory on the
   hard drive containing the MS-DOS files.

5. Use the DISKCOPY command to copy the contents of the disks, as follows:

   diskcopy a: a: (for a single floppy drive)

   -or-

   diskcopy a: b: (for two 5.25-inch 360K floppy drives)

6. Repeat steps 3-6 for the six Upgrade disks.

The DISKCOPY command will copy the the volume label of the Upgrade disks in
addition to the disk contents.

DISKCOPY requires that the source and destination disk have the same format.

The COPY and XCOPY commands can also be used to backup the disks. The volume
label is not copied with these commands.

Note: The volume label from the Upgrade disk is required on the corresponding
backup disks. There are two ways to create a volume label:

 - When formatting a disk, you can enter the volume label.

 - If a disk is already formatted, you can use the LABEL command:

   label [drive]:

   (Where [drive] is the location of the disk to be labeled.)

The format for the volume label is DISK followed by six spaces, then the number
of the disk. For example, the volume label for disk 1 is:

   Disk      1

To Back Up 3.5-inch Disks to 3.5-inch Disks
-------------------------------------------

Three 3.5-inch blank disks are required.

To back up 3.5-inch disks, follow steps 1-6 above (the same procedure is used).

To Back Up 5.25-inch Disks to 3.5-inch Disks
--------------------------------------------

These steps assume that drive A is 5.25-inch and drive B is 3.5-inch. Six
3.5-inch formatted blank disks are required.

1. Boot your computer with the current version of DOS.

2. Insert disk 1 in drive A.

3. Insert a blank formatted disk in drive B.

4. Move to the drive C root directory (C:\>) or to the directory on the hard
   drive containing the MS-DOS files.

5. Enter the following at the command prompt:

   " copy a:*.* b:" (without the quotation marks)

   (The XCOPY command may also be used.)

6. Repeat steps 2-5 for the remaining Upgrade disks.

Note: The volume label from the upgrade disk is required on the corresponding
backup disk.

For additional information regarding the Microsoft MS-DOS 5.0 Upgrade License
Agreement, please refer to the License card enclosed with the Upgrade package.

Additional query words: 5.00 noupd

======================================================================
Keywords          :  
Technology        : kbMSDOSSearch kbMSDOS500
Version           : MS-DOS:5.0

=============================================================================

THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS
PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND.  MICROSOFT DISCLAIMS
ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  IN NO
EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR
ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF
MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.  SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES
SO THE FOREGOING LIMITATION MAY NOT APPLY.

Copyright Microsoft Corporation 1999.