The information in this article applies to:
- Microsoft Exchange Server, version 5.0
SUMMARY
This article lists steps to help you troubleshoot problems when you
attempt to connect to the Internet Mail Server from an e-mail client
using post office protocol version 3 (POP3). These steps are based on
information in the Request for Comments (RFC) 1725 and RFC 1939
specifications.
MORE INFORMATION
Basic Troubleshooting
If you are unable to connect to the Internet Mail Server from an e-mail
client using POP3, use the following steps to troubleshoot the problem.
After performing each step, check to see if the issue has been resolved.
- Verify that the e-mail client is POP3-compliant. Many e-mail clients
are not POP3-compliant. In particular, many newer e-mail clients
support Internet Mail Access Protocol version 4 (IMAP4). Microsoft
Exchange Server does not support IMAP4. Microsoft Exchange Server
supports POP3 as defined in the RFC 1725, RFC 1734, RFC 1939, and
RFC 1953 specifications.
- Use the Telnet tool to connect to the Microsoft Exchange Server. To do
so, follow these steps:
a. On the e-mail client, start Telnet. For the host name, type the
name of the Microsoft Exchange Server computer, and for the port
type, type 110. If a "term type" is requested, do not type
anything. For example, type the following command to start Telnet:
telnet <server> 110
where <server> is the name of the Microsoft Exchange Server
computer. If you are running Windows 95, Windows NT Workstation, or
Windows NT Server, you can type the above command at a command
prompt or in the Run dialog box. If you are running Windows NT
Workstation or Windows NT Server version 3.51, you can open the Run
dialog box from the File menu or the task list.
When you type the above command and then press ENTER, a message
similar to the following should be displayed:
+OK Microsoft Exchange POP3 server version 5.0.1457.10 ready
NOTE: The version number might be different, but it should be
5.0.1457.10 or later.
b. Enable local echo for the current Telnet session. To do so, on the
Terminal menu, click Preferences, click the Local Echo check box to
select it, and then click OK.
c. Type the following command, and then press ENTER:
user <domain>\<username>\<mailbox>
where <domain> is the name of the domain in which the user's
account is located, <username> is the user name, and <mailbox> is
the user's mailbox. Note that the <mailbox> portion of the above
command is only necessary if it is different from the <username>
portion. When you press ENTER, "+OK" (without quotation marks)
should be displayed.
d. Type the following command, and then press ENTER:
pass <password>
where <password> is the user's password. When you press ENTER, the
following message should be displayed:
+OK User successfully logged on
e. To determine if the user has new messages, type "stat" (without
quotation marks), and then press ENTER. After you press ENTER, the
following message should be displayed:
+OK <x> <yyyy>
where <x> is the number of new messages and <yyyy> is the total
size of the messages in bytes. This is known as a "drop listing."
f. To end the Telnet session, type "quit" (without quotation marks),
and then press ENTER. When you press ENTER, a message similar to
the following should be displayed:
+OK Microsoft Exchange POP3 server version 5.0.1457.10
signing off
NOTE: The above POP3 commands can only be used to troubleshoot problems
when you attempt to receive messages. A POP3 client uses Simple Mail
Transfer Protocol (SMTP) to send messages. For information about how
troubleshoot problems when you attempt to send messages, please see the
following article in the Microsoft Knowledge Base:
ARTICLE-ID: Q153119
TITLE : XFOR: Telnet to Port 25 of IMC to Test IMC Communication
Additional Troubleshooting
If the problem still occurs, perform these steps. After performing each
step, check to see if the issue has been resolved.
- Verify that the POP3 protocol is enabled for the site Protocols
container and the Protocols container on the server.
- Verify that POP3 support is not disabled for the user's mailbox.
- Verify that the client can ping the server using the server's Internet
protocol (IP) address and the server's computer name.
- Run the Rpings.exe tool that is located on the Microsoft Exchange
Server CD-ROM. Rpings.exe runs on the server; a client program must
also be run on the client. If you are running Windows or Windows for
Workgroups version 3.x, run Rpingc16.exe on the client. If you are
running Windows 95, Windows NT Server, or Windows NT Workstation, run
Rpingc32.exe on the client.
NOTE: The Rpings.exe tool is used to determine if the client can
connect to the server using remote procedure call (RPC). POP3 clients
do not connect to the Microsoft Exchange Server computer using RPC.
- Try to use the Microsoft Exchange Windows NT client to connect to the
server from the same computer on which Microsoft Exchange Server is
installed.
- Try using a different e-mail client. For example, use the Microsoft
Exchange client and the Internet Mail information service included
with Microsoft Plus! or use Microsoft Internet Mail and News. The
Internet Mail information service is included with Windows NT Server
and Windows NT Workstation 4.0. For information about how to obtain
Internet Mail and News, please see the following article in the
Microsoft Knowledge Base:
ARTICLE-ID: Q154457
TITLE : Availability of Microsoft Internet Mail and News
If the problem still occurs, contact the manufacturer of the e-mail
client for additional assistance.
MORE INFORMATION
For additional information, please see the following articles in the
Microsoft Knowledge Base:
ARTICLE-ID: Q161116
TITLE : XCLN: POP3 Supported Command Set for Exchange Server 5.0
ARTICLE-ID: Q155048
TITLE : XCLN: Troubleshooting Startup of Windows Client Using
TCP/IP
ARTICLE-ID: Q153119
TITLE : XFOR: Telnet to Port 25 of IMC to Test IMC Communication
|