DOCUMENT:Q165445  19-DEC-1999  [exchange]
TITLE   :XCON: How to Configure TP4 Protocol over Routers
PRODUCT :Microsoft Exchange
PROD/VER:winnt:4.0,5.0,5.5
OPER/SYS:
KEYWORDS:kbusage exc4 exc5 exc55

======================================================================
-------------------------------------------------------------------------------
The information in this article applies to:

 - Microsoft Exchange Server, versions 5.5, 4.0, 5.0 
-------------------------------------------------------------------------------

SUMMARY
=======

When configuring the TP4 protocol over routers, if the router is capable of
understanding the ES-IS protocol there is no need to specify static routes or
default gateways. If the router doesn't understand the ES-IS protocol, you might
need to add Static Routes to the OSIRTE file.

This file is located in your %windir%\system32\drivers\etc directory. The file
includes comments on how to add routing table entries.


The following is a sample OSIRTE file.

   ;
   ;       Static Routing table entries use the format as follows:
   ;
   ;       NSAP:MAC/X.121 address:Priority:CardChoice
   ;
   ;       Where;
   ;       NSAP = The remote ES's NSAP you want to communicate with
   ;
   ;       MAC = The ethernet address and is always an Hex format
   ;
   ;       X.121 address must be encoded in hex as 703701020304..and so on
   ;
   ;       Priority =  0 or 1.
   ;
   ;       CardChoice = ndis device name. I know it is cumbersome
   ;       Use the System-CurrentControl-services-Isotp-Linkage->bind of RegDB
   ;       Key values as shown. (NOTE: Streams is omitted from ndis_dev name)
   ;
   ;       NO BLANK SPACES ALLOWED IN THESE ENTRIES
   ;       RemoteNSAP can be ASCII. A $ implies HEX encoding for 1st & 2nd
   ;       field.
   ;
   ;       Lets take an example. If you want to route a destination whose
   ;       NSAP is FIRSTPLACE on Etherlink 3 card to an IS system whose
   ;       MAC address is 010203040506 the entry would loook like
   ;
   ;       FIRSTPLACE:$010203040506:1:\Device\Elnk31
   ;
   ; The static routes are as defined below
   ;
   ; The 1st line is priority 0 route for NSAP 474747(hex)
   ; The 2nd line is alternate route for NSAP GEE ( hex:474747)
   ; Where as 2rd line is highest priority for NSAP GGG but on FDDI card.
   ; Now the card with subnet id = 0 will be the 1st one used.
   ;
   ;$474747:$112233445566:0:\Device\Elnk31
   ;GGG:$010203040506:1:\Device\Elnk31
   ;GGG:$010203040506:0:\Device\SkFddiFe2

Additional query words:

======================================================================
Keywords          : kbusage exc4 exc5 exc55 
Technology        : kbExchangeSearch kbExchange500 kbExchange550 kbExchange400 kbZNotKeyword2
Version           : winnt:4.0,5.0,5.5

=============================================================================

THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS
PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND.  MICROSOFT DISCLAIMS
ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  IN NO
EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR
ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF
MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.  SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES
SO THE FOREGOING LIMITATION MAY NOT APPLY.

Copyright Microsoft Corporation 1999.